Search Criteria
Items meeting the search criteria
Item No: ALP KIT30
Drill & Screw Set,
30 pcs [KIT 30]
Alpen multipurpose drill bit and screwdriver set in a handy plastic carry
case. Versitile and handy for a quick job on the
jobsite
Range
of application:
For drilling into wood, steel and masonry with the added
convenience of screwdriver bits ready at hand.
For drilling into:
....
R 1,350.16
Ex VAT:R 1,174.05
Item No: ALP KIT22
Drill & Screw Set, 22 pcs [KIT 22]
Alpen multipurpose drill bit and screwdriver set in a handy plastic carry
case. Versitile and handy for a quick job on the
jobsite
Range
of application:
For drilling into steel and masonry with the added
convenience of screwdriver bits ready at hand.
For drilling into:
Masonry ....
R 929.03
Ex VAT:R 807.85
Item No: TCAC012-2
Annular Cutters 55mm long
Annular Cutter: &O/; 12 mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 481.71
Ex VAT:R 418.88
Item No: TCAC013-2
Annular Cutters 55mm long
Annular Cutter: &O/; 13
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 481.71
Ex VAT:R 418.88
Item No: TCAC014-1
Annular Cutters 30mm
Annular Cutter: &O/; 14
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 364.26
Ex VAT:R 316.75
Item No: TCAC015-1
Annular Cutters 30mm
Annular Cutter: &O/; 15
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 345.58
Ex VAT:R 300.50
Item No: TCAC017-2
Annular Cutters 55mm long
Annular Cutter: &O/; 17
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 507.27
Ex VAT:R 441.10
Item No: TCAC020-1
Annular Cutters 30mm
Annular Cutter: &O/; 20
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 457.99
Ex VAT:R 398.25
Item No: TCAC021-1
Annular Cutters 30mm
Annular Cutter: &O/; 21
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 460.52
Ex VAT:R 400.45
Item No: TCAC021-2
Annular Cutters 55mm long
Annular Cutter: &O/; 21 mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 611.74
Ex VAT:R 531.95
Item No: TCAC022-2
Annular Cutters 55mm long
Annular Cutter: &O/; 22
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 644.69
Ex VAT:R 560.60
Item No: TCAC023-1
Annular Cutters 30mm
Annular Cutter: &O/; 23
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 507.50
Ex VAT:R 441.30
Item No: TCAC023-2
Annular Cutters 55mm long
Annular Cutter: &O/; 23
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 685.98
Ex VAT:R 596.50
Item No: TCAC026-1
Annular Cutters 30mm
Annular Cutter: &O/; 26
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 641.07
Ex VAT:R 557.45
Item No: TCAC026-2
Annular Cutters 55mm long
Annular Cutter: &O/; 26
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 804.20
Ex VAT:R 699.30
Item No: TCAC030-2
Annular Cutters 55mm long
Annular Cutter: &O/; 30
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 892.17
Ex VAT:R 775.80
Item No: TCAC031-1
Annular Cutters 30mm
Annular Cutter: &O/; 31
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 833.08
Ex VAT:R 724.42
Item No: TCAC033-1
Annular Cutters 30mm
Annular Cutter: &O/; 33
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 804.20
Ex VAT:R 699.30
Item No: TCAC036-1
Annular Cutters 30mm
Annular Cutter: &O/; 36
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 864.63
Ex VAT:R 751.85
Item No: TCAC036-2
Annular Cutters 55mm long
Annular Cutter: &O/; 36
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,208.31
Ex VAT:R 1,050.70
Item No: TCAC038-1
Annular Cutters 30mm
Annular Cutter: &O/; 38 mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
the ..
R 1,060.29
Ex VAT:R 921.99
Item No: TCAC044-1
Annular Cutters 30mm
Annular Cutter: &O/; 44
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 1,425.76
Ex VAT:R 1,239.79
Item No: TCAC044-2
Annular Cutters 55mm long
Annular Cutter: &O/; 44
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,813.23
Ex VAT:R 1,576.72
Item No: TCAC045-2
Annular Cutters 55mm long
Annular Cutter: &O/; 45
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,783.29
Ex VAT:R 1,550.69
Item No: TCAC0001
Morse Taper to Weldon adaptor
MT3 to Weldon Adaptor
Morse Taper 3 adaptor that accept cutters with a 3/4 inch Weldon shank
What is a Weldon Shank?
The term comes from the Weldomn Tool Company. The Weldon shank was the first straight shank with a locking drive flat....
R 1,168.52
Ex VAT:R 1,016.10
Item No: TCAC0002
Morse Taper to Weldon adaptor
MT2 to Weldon Adaptor
Morse Taper 2 adaptor that accept cutters with a 3/4 inch Weldon shank
What is a Weldon Shank?
The term comes from the Weldomn Tool Company. The Weldon shank was the first straight shank with a locking drive flat....
R 1,333.43
Ex VAT:R 1,159.50
Item No: TCAC0004
Annular Cutter Pilot Pin
6.3 mm Pilot Pin for
30 mm Annular Cutters
Pilot pin with length of 79 mm specifically for annular cutters (broach
cutters) with a cutting length of 30 mm.
....
R 34.06
Ex VAT:R 29.62
Item No: TCAC0005
Annular Cutter Pilot Pin
6.3 mm Pilot Pin for
55 mm Annular Cutters
Pilot pin with length of 102 mm specifically for annular cutters (broach
cutters) with a cutting length of 55 mm.
....
R 44.03
Ex VAT:R 38.29
Item No: TCAC014-2
Annular Cutters 55mm long
Annular Cutter: &O/; 14
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 453.62
Ex VAT:R 394.45
Item No: TCAC016-2
Annular Cutters 55mm long
Annular Cutter: &O/; 16
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 515.49
Ex VAT:R 448.25
Item No: TCAC018-1
Annular Cutters 30mm
Annular Cutter: &O/; 18
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 411.01
Ex VAT:R 357.40
Item No: TCAC019-1
Annular Cutters 30mm
Annular Cutter: &O/; 19
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 419.23
Ex VAT:R 364.55
Item No: TCAC024-2
Annular Cutters 55mm long
Annular Cutter: &O/; 24
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 749.17
Ex VAT:R 651.45
Item No: TCAC027-2
Annular Cutters 55mm long
Annular Cutter: &O/; 27
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 925.55
Ex VAT:R 804.83
Item No: TCAC028-1
Annular Cutters 30mm
Annular Cutter: &O/; 28
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 584.20
Ex VAT:R 508.00
Item No: TCAC032-1
Annular Cutters 30mm
Annular Cutter: &O/; 32
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 795.92
Ex VAT:R 692.10
Item No: TCAC032-2
Annular Cutters 55mm long
Annular Cutter: &O/; 32
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 840.31
Ex VAT:R 730.70
Item No: TCAC033-2
Annular Cutters 55mm long
Annular Cutter: &O/; 33
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 927.88
Ex VAT:R 806.85
Item No: TCAC035-1
Annular Cutters 30mm
Annular Cutter: &O/; 35
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 845.42
Ex VAT:R 735.15
Item No: TCAC035-2
Annular Cutters 55mm long
Annular Cutter: &O/; 35
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,098.37
Ex VAT:R 955.10
Item No: TCAC038-2
Annular Cutters 55mm long
Annular Cutter: &O/; 38
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,397.57
Ex VAT:R 1,215.28
Item No: TCAC040-2
Annular Cutters 55mm long
Annular Cutter: &O/; 40
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 1,373.27
Ex VAT:R 1,194.15
Item No: TCAC042-1
Annular Cutters 30mm
Annular Cutter: &O/; 42
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 1,264.60
Ex VAT:R 1,099.65
Item No: TCAC045-1
Annular Cutters 30mm
Annular Cutter: &O/; 45
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 1,340.27
Ex VAT:R 1,165.45
Item No: TCAC046-1
Annular Cutters 30mm
Annular Cutter: &O/; 46
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 1,527.90
Ex VAT:R 1,328.61
Item No: TCAC050-2
Annular Cutters 55mm long
Annular Cutter: &O/; 50
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 2,277.33
Ex VAT:R 1,980.29
Item No: TCAC012-1
Annular Cutters 30mm
Annular Cutter: &O/; 12 mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
the ..
R 373.39
Ex VAT:R 324.69
Item No: TCAC013-1
Annular Cutters 30mm
Annular Cutter: &O/; 13
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 364.26
Ex VAT:R 316.75
Item No: TCAC015-2
Annular Cutters 55mm long
Annular Cutter: &O/; 15
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns abou..
R 460.52
Ex VAT:R 400.45
Item No: TCAC016-1
Annular Cutters 30mm
Annular Cutter: &O/; 16
mm
One
way to avoid dimpling and deburring while making holes in tube and pipe is to use
annular cutters. Because annular cutters are hollow on the inside, there is no dead-zone
resistance to overcome.
Using a twist drill to make holes in pipe or tubing can prompt concerns about
..
R 391.35
Ex VAT:R 340.30
Categories meeting the search criteria
No Search criteria specified
Brands meeting the search criteria
No Search criteria specified
Information
No Search criteria specified